It’s been a couple of years since I built my
Boba Fett suit, but over the last few weeks I’ve been working on a jetpack. There’s a reason that I put this part off – it’s an incredibly difficult part to build from scratch. But since the unpainted resin kit costs $350, I chose to make the pack out of sintra and upholstery tubing which I managed to pick up for free. Other than that, it was just the cost of Bondo, spray paint, some wooden balls, liquid mask, and a few wooden dowels.
This was my first time to do something so elaborate, but I’m very pleased with the results.
Cutting out the bottom from 1/4″ sintra. First time to work with this material, and I love it.
Back of jetpack also cut from 1/4″ sintra
I decided the easiest way to make these was to heat a 1/8″ piece of sintra and press it down on a small piece of tubing (shown on the right).
Finished fuel canister ends
Cardboard tubes (from tapestry shop) cut to length and bottoms capped
Carefully cutting out the vent slots
The bottom exhaust vent applied with spacers.
Attaching the bottom to the back using pvc glue. The small piece of pipe was my first attempt, but then I decided to cut some small pieces of sintra, heat them, and form them to a 90 degree angle then use them as brackets.
I used another piece of sintra to thicken this area at the top of the pack.
Checking the fit. Getting ready to trim off the edge of the sintra to match the back.
Attaching the fuel caps with Gorilla Glue.
Fuel caps with the ends attached using pvc.
Holding pieces in place while they dry.
This piece is way oversized. Allowed me to cut this flush.
This is a happy moment. It’s really starting to come together.
Holding the fuel canisters in place while the glue dries.
Creating an ugly shim to hold up this strip.
I hated the thought of the thrusters being misaligned from one another, so I drilled a small hole through the whole pack and threaded a small piece of dowel through there. The other end of this pvc pipe has a flat end that I capped, and I also put the dowel through there and glued it.
Bottom caps in place and drying.
Drawing out the cones. I used an online tool to get the correct angle and radius lengths.
All the cone pieces have been cut out and are ready to form.
In the process of cutting out vents.
This is probably the most difficult piece in the whole suit. Pretty happy it turned out so well.
Whether dumb luck or brilliance, I decided to glue a fitting into this cardboard tube. Since I didn’t glue this piece, it allows me to remove the missile thruster for easier transport.
Additional box areas have been roughed out.
I used a clamp to hold this piece in place while I was drilling the attachment location.
I decided to make these buttons out of four stacked washers of identical size with one small washer in the middle.
Trusters are ready to glue.
Gluing the thrusters.
Gluing the shaped cones.
Gluing the top vent.
Not too bad. :)
Fitting my missile for the first time. I was so happy until I realized that the bottom cone of the missile wasn’t really the right shape.
Mixing the Bondo.
Applying automotive filler – Bondo.
Missile fitted with fins.
After applying primer to the missile booster.
I really needed to do another coat of Bondo, but I couldn’t help myself – I went ahead and sprayed it with primer.
I nearly gave up and started painting everything until I read an article about getting everything smooth beforehand. Though I had already painted a silver coat, I sanded everything smooth. The process left a lot of texture and metal-looking colors, so I was happy to use this as a base.
Masking off to prepare for painting the orange areas.
Masking off to paint the blue areas. I also used some liquid mask to paint over the areas where the metal should show through.
If you look closely, you can see some of the rough areas in the blue. These are the places where I applied liquid mask.
Masking off the area around a stripe.
While the blue was drying, I decided to paint this black stripe
Making corrections to the missile to extend the bottom cone.
I used my fingers to find the masked areas and remove them. So happy with the results!
Masking off the whole jetpack so that I can paint the top vents. I also applied liquid mask here.
The accumulating mess and debris of my work bench. This was a clean piece of MDF board when I started on the jetpack.
Masking in preparation for painting the red side areas.
This is the part referred to as the stabilizing gyro. I made mine out of a dry-erase marker that I emptied and cut in half.
Painting the gyro.
Painting the top sections of the fuel canisters.
Painting the final light gray sections.
This was another one of those moments when I thought, “maybe I will finish this some day.”
Painting the top of the fuel canisters. The caps have been masked off.
Masking off the bottom of the fuel canisters.
Adding a black stripe to the main tube.
Gluing on the new bottom portion of the missile.
Here, I’ve added stripes and symbol details to the fuel canisters.
Painting the base coat on the missile.
Adding additional color to the missile. You can see the uneven areas where liquid mask was applied before painting.
Detail after additional weathering has been applied.
Everything finally assembled together!
For a full writeup, see my full list of instructions on
Instructables. This project has been featured on:
For photos of the work in progress, go here .
mentioned the other day, I’ve been building a Boba Fett costume for Halloween. It began with my wife’s innocent comment that it would be fun to dress up as Star Wars characters as a family, and when the costume I bought online didn’t live up to my expectations, I began to research how I might build my own costume. Fortunately, there’s a ton of great tips online, and I quickly found myself totally hooked. I love a good project, and without a doubt, this has been the best project I’ve ever attempted.
Below are photos of my costume through the process. I’ll continue to update this post as I add new components.
Rather than just serving as an example of my compulsiveness, I hope that others attempting to build a Boba Fett costume might find some ideas here and avoid some problems I encountered.
I started off by trying to paint the toy blaster to look more realistic.
First coat of paint.
Finished Boba Fett blaster.
Cutting my torso armor from and old box.
Front armor cut out of cardboard.
This is the flight suit that I purchased from an military surplus store. Wrong color and wrong pockets but a nice fit.
Cutting out sheet aluminum and wrapping the cardboard. I took a break to get some gloves after cutting myself.
First piece wrapped. Nice start.
My wife took this pic with my son right before I was banished from the living room, never to return with this project again.
Covering the sharp back edges of the aluminum with duct tape.
Spray painting the finished armor.
Armor after battle scarring.
Starting work on the knee armor.
I learned that PVC can be heated and shaped using a heat gun.
With the pieces shaped, I marked up each piece for my trim lines.
Using a dremel to cut the PVC. This is a very messy process. PVC dust everywhere.
Knee armor is completely cut out.
Side pieces cut from wood and screwed to the PVC using a countersink from the inside.
Beginning the shoulder armor.
Wrapping the shoulder armor in sheet aluminum.
Both shoulders cut and wrapped.
Both pieces shaped by hand.
First layer of paint for the knee and shoulder armor. This is the point at which I knew there was no going back. I was completely hooked.
The only canvas I could find for the cape was the wrong color, but through experimentation I discovered that I could bleach it to the army green color I was looking for.
By this time, I realized that there were too many fabric components in the suit to continue without learning to sew.
Next up were the side belt pockets. I had no pattern, but I figured out how I wanted to try piecing it together.
Nearly finished side pocket turned inside out for sewing.
Finished belt pockets! I left the belt loop material unattached until I had the belt created and knew how big the loops needed to be.
Side view of the completed pockets. This was a proud moment. :)
Distressed and finished knee armor. Though the side blasters aren’t exactly the right size, I love how these turned out.
Masking off the left shoulder for the Mandalorian insignia.
Beginning work on the neck piece. I just zigzagged the material back and forth and taped it down as I went along.
Side view of the neck seal in progress.
I attached a round piece of cloth at the bottom so that I’d have something to tuck into my shirt and keep there from being any gaps.
Neck seal laid out flat.
Using one of my daugher’s markers to rough in the design. I should have checked to make sure I could wipe it off before doing this. Ended up being a pain.
Design painted onto the shoulder armor.
After painting over all the marker.
After failed attempts to bleach and dye the flight suit, I resorted to trying spray paint. This was a pretty miserable start, and I wasn’t sure how to proceed.
Beginning work on the ammo belt.
Cutting out the ammo belt.
Finished shoulder armor.
My wife helped me to finally come up with a solid solution for attaching the knee armor.
This rope belt is worn under the ammo belt. I didn’t have to make it since it’s a horse belt (not kidding), but here I spray painted the belt.
Velcro sewn to the back of the belt to match the look of the movie and eyelets installed. This was another very happy moment.
Rope belt dry and ready to go!
Since all the pockets on the flight suit were the wrong size and in the wrong places, I ripped out all the existing pockets. I would salvage this material for the new pockets I would make.
Beginning work on my first thigh cargo pocket.
Thigh pockets installed. It’s looking pretty patchy here, but things are starting to come together.
Working on the pocket flap.
Thigh and shin pockets are complete with hardly a scrap of leftover fabric.
Beginning work on the ammo belt. Here I used my chop saw to cut eight identical blocks of wood.
Blocks of wood sanded and ready to go.
Creating a pattern for the material to wrap the block.
Copying and cutting the pattern. Tedious work.
Detailed sewing. Stitching the flap portion for each pocket.
Attaching the pockets to the belt.
This was a mess!
The belt with all the pockets attached.
Now, I began wrapping each block and gluing it together with super glue.
All the sides wrapped.
Completed ammo belt with pouches! Hurray!
Sporting the ammo belt! So happy that it turned out like I was hoping.
Flattening out a section of PVC for the shin tools.
Sketching out the shin tools.
Cutting out the back portion of the armor from my old box.
Cutting the aluminum to wrap the cardboard.
Bad side of the back armor.
Armor shaped by hand and sanded to prep for paint.
Back armor painted.
I laid a tshirt on top of my fabric, lined up the seams, and traced that shape for my armor vest – making adaptations for the vest fit.
Vest in process. I think it was mostly luck that the thing fit. Backwards from what I anticipated. Setting seam marks, and wondering how to get this thing off of myself without waking up my wife for help in the middle of the night.
Vest shoulder pieces cut and stitched.
Using epoxy to attach bolts to the corners of the armor. I never would have thought this would be a good idea, but someone online suggested it.
I started out with the JB Weld steel stick epoxy at first, but I wish I had just used the regular JB Weld.
Fitting paper to the back of the armor and marking the bolt holes to get a good fit when making holes in the vest.
All armor fitted with paper patterns.
Taped the paper patterns in place and marked the bolt locations.
Vest with eyelets installed at each of the bolt locations.
Vest with armor bolted onto the reverse. From here, I attempted cutting off the extra bolt on each one, but that was a miserable failure. Should have cut all the bolts before attaching them to the armor. Had to reattach most of them.
Considering using the pvc for the ground-level buildout of the gauntlets. Not sure if this is a good idea or not.
Cutting out the shin tools from the flattened piece of PVC.
Beginning to shape out the knife.
A lot of imperfections due to the inexact process of shaping with a dremel tool, but still looking close enough that I was happy with the results of these two pieces.
I had to make a new front neck piece in order to make it connect to the back piece.
Drilling holes to connect the front and back.
Underside of connecting slot.
Old keyboard keys used for shoulder studs. Used JB Weld to secure nut to the bottom of each.
Top of the shoulder studs after painting.
Beginning work on the gauntlet missile.
Front cone near completion.
Hoping I can turn these canvas shoes into boots.
Using superglue to affix vinyl to the shoes.
I purchased this piece for the gauntlet on Ebay. It’s a resin cast of a calculator that was used for the authentic suit.
Beginning work on the gauntlets.
Cable fittings for the flame thrower.
Starting on the second boot.
First layer of pain on the boot uppers.
Weathering the paint. Here you can see the elastic side of the boot that is stitched in.
Applying piping to the boots. I used painted stereo wire and superglue.
Masking the visor on the toy helmet to apply paint.
Back of the helmet before paint.
Side of the helmet before paint.
Silver and black paint applied.
Helmet pieces glued together and filled with Bondo.
Green paint applied.
Masking off the helmet for red paint.
Ready for red paint application.
Back of the helmet.
All paint applied. Way too clean and neat for Boba Fett.
After distressing and battle scarring.
My garage workspace with several pieces in progress.
Forming aluminum for the front of the shoes.
Metal screwed into the front of the shoes and filled with Bondo. Sharpened wooden dowels added for spikes.
Other than a bit of paint on the front of the shoes, they’re pretty much complete here.
Starting work on the left gauntlet.
RadioShack buttons for left gauntlet.
Beginning work on details for right gauntlet.
Bottom half of left gauntlet.
Gauntlet halves are starting to take shape.
Fitting the missile.
Installing nails for right gauntlet weapons.
Button area masked off and ready to paint.
First layer of paint!
Pics of completed costume
For a few weeks, my daughter and I have talked about making a tree house for some of her toys. This weekend we decided to go for it.
Update 1/10/15: I am now selling this same treehouse through my
Sketching the Plans
Cutting out the Pieces
Sanding and Rounding Edges
Dowels for added stability
Ground Level Complete
Gluing and Clamping
Waiting for the Glue to Cure
With Toy Animals
Total material cost was about $20.
This was a fun project, and I anticipate building additional elements over the next few months.
Update 1/10/15: I am now selling this same treehouse through my